- How loud should my mix be?
- What Hz is best for bass?
- How high should gain be on mic?
- What should I set my HPF and LPF to?
- What is a good crossover frequency?
- What is gain on an amp?
- How do you adjust a monoblock amp?
- What tones to use when setting gains?
- What volume level should I mix at?
- How do you set low pass frequency?
- What should subsonic filter be set to?
- Should power amps be turned all the way up?
- What is proper gain staging?
- What is gain staging in logic?
- Is 40 Hz low enough?
- What Hz should I set my car speakers to?
- Is 80 Hz the best crossover?
- When should I use high pass filter?
- What should I set my low pass filter to?
How loud should my mix be?
So long as your mixes give the mastering engineer room to work, and cover your noise floor, then you’re in a good range.
I recommend mixing at -23 dB LUFS, or having your peaks be between -18dB and -3dB..
What Hz is best for bass?
20-120 HzA 20-120 Hz rating is best for bass in most subwoofers. The lower the Hz, the more is the bass you can get. Some of the best subwoofers in the market have this Hz range. If you are buying a subwoofer that has a fixed Hz rating, you should ensure it is lower than 80 Hz if the bass is important to you.
How high should gain be on mic?
From our general nominal values noted above, a 44 dB to 64 dB gain boost would do the trick. Mic inputs expect mic level signals. If a mic input has a built-in preamplifier, the preamp should have enough gain to bring the mic signal up to line level.
What should I set my HPF and LPF to?
You usually set the HPF with a steep slope say 24db/octave because you are trying to protect the sub from damage and a 12-18db/octave on the LPF because you want it to kinda “blend” in with your mids. The steeper the slope (db/octave) the less your sub will creep into the neighboring frequencies.
What is a good crossover frequency?
What is the recommended crossover frequency for a subwoofer? For THX Certified and non THX Certified home theater systems, 80 Hz is the recommended setting. However, you can set the crossover (LPF) between 80 Hz – 120 Hz based on which setting sounds best for your system.
What is gain on an amp?
On some amps, you can control the level or strength of the signal sent through this first stage; this control is called “gain” (also often labeled as “drive”). … Setting the gain control sets the level of distortion in your tone, regardless of how loud the final volume is set.
How do you adjust a monoblock amp?
HOW TO TUNE A MONOBLOCK AMPFirstly, keep all your head unit settings at flat i.e. all bass boosts and other effects should be at the minimum level.Turn the head unit volume to the loudest it can go without any distortion.Turn down all gains and bass boosts to the minimum.Turn up the low pass to the maximum level.More items…•
What tones to use when setting gains?
Instructions for setting amp gain using test tones Back off the volume until the hum returns, and write down or mark the volume setting. Repeat Step 2, noting the top clean volume settings, using the 100, 400, 800, and 1K Hz tones. Pick the tone with the lowest clean volume setting and play it again at that setting.
What volume level should I mix at?
A good rule of thumb is that your volume level should be low enough to allow for conversation without raising your voice.
How do you set low pass frequency?
Turn your sub amp’s gain to its lowest, most counter-clockwise position. Switch its low-pass filter on and set it as high, clockwise, as it will go. If it has a bass boost, turn it off.
What should subsonic filter be set to?
Since the Hz setting on the subsonic filter is the start of a slope, not a cutoff, we want to set it higher than 20 Hz. The sweet spot for getting some pounding bass without destroying your subwoofer is between 25 Hz and 35 Hz.
Should power amps be turned all the way up?
The level controls of the power amps should be set so you maintain consistent gain staging throughout your system, while allowing ample headroom. If you need to turn them up all the way to achieve that (as is often the case) then you certainly should.
What is proper gain staging?
Gain staging, or gain structuring, is the act of setting the gain for each amplification stage (gain stage) in a sound system to achieve a target system volume that minimizes noise and distortion. Said another way, proper gain staging allows your sound system to achieve the best signal-to-noise ratio.
What is gain staging in logic?
What is gain staging? Gain staging is level management. It comes from the analogue days where it was essential to get a good signal-to-noise ratio whilst preventing clipping the channel. … Gain staging was also very necessary to make sure that the level going into each hardware unit was optimal.
Is 40 Hz low enough?
below 40 hz? yes, quite necessary. below 30 is where it gets less important. 30-45ish would be what most would consider real subbass….you may not hear it with a standard computer speaker setup, but you roll off anything below 50, there will be something noticeably missing on the dancefloor.
What Hz should I set my car speakers to?
Thus, the recommended settings are a HPF (5000 Hz) for the front tweeters, a HPF (80 Hz) for front midrange, a HPF (80 Hz) for rear speakers and 12 dB or 24dB slope. If rear speakers (passive) are added to this system, the settings will change a little bit.
Is 80 Hz the best crossover?
The most common crossover frequency recommended (and the THX standard) is 80 Hz. … Mid-size center, surround, bookshelf: 80-100 Hz. Large center, surround and bookshelf: 60-80 Hz. Very large center, surround, bookshelf: 40-60 Hz.
When should I use high pass filter?
If you are broadcasting or reinforcing sound outside, and even your best windscreen can’t keep out the persistent low-frequency rumble from wind noise, then stopping it right at the source may be your best option. Highpass filters are excellent for this application.
What should I set my low pass filter to?
As a general rule, the Low-Pass Filter should be set at a value approximately equal to (or below) 70% of your main speaker’s lowest frequency response. For example, your speaker’s frequency response goes down to 43Hz. 70% of 43Hz equals 30.1, so you should set the subwoofer’s low pass filter to 30Hz.